Traxxas 48077 Manuel d'utilisateur télécharger pdf (Page 38)

•

NITRO 4-TEC 3.3

ADVANCED TUNING GUIDE

Press MENU to move through options.

Press SET to select an option.

Press MENU to move through options.

Press SET to select an option.

Enter Programming

Press and hold

MENU for 3 seconds

Steering Sensitivity (Expo)

One Blink Red

Electric

One Blink Red

Unlock

One Blink Red

Servo Reversing

One Blink Red

Servo Reversing

One Blink Red

Conﬁrm Deletion

One Blink Red

Multi-Function Knob

One Blink Green

Channel Setup

Two Blinks Green

Mode Selection

Three Blinks Green

Traxxas Link

Four Blinks Green

Steering (Channel 1)

One Blink Green

Model Locking

One Blink Green

Throttle (Channel 2)

Two Blinks Green

Delete Model

Two Blinks Green

Throttle Sensitivity (Expo)

Two Blinks Red

Nitro

Two Blinks Red

Lock

Two Blinks Red

Sub-Trim

Two Blinks Red

Sub-Trim

Two Blinks Red

Steering % (Dual Rate)

Three Blinks Red

Unlock All

Three Blinks Red

End Points

Three Blinks Red

Braking %

Four Blinks Red

Reset End Points

Four Blinks Red

Throttle Trim

Five Blinks Red

Knob Disabled

Six Blinks Red

Press

SET

Press

SET

Press

SET

Press

SET

Press

SET

Press

SET

Press

SET

Press

SET

Press SET to reverse

servo direction.

Press SET to reverse

servo direction.

Press SET to restore

factory default endpoints.

Reset End Points

Four Blinks Red

Press SET to restore

factory default endpoints.

Use knob to adjust

sub-trim. Press SET to save.

Use knob to adjust sub-

trim. Press SET to save.

Use steering wheel to

adjust. Turn right to desired

end point, press set to save.

Turn left to desired endpoint and press set to save.

To reset max throw: Let go of controls and press SET.

Note: The transmitter is “live” during programming

so you can test the settings real time without having

to exit the menu tree.

End Points

Three Blinks Red

Use trigger to adjust. Pull

back to desired end point,

press set to save. Push

forward to desired endpoint and press set to save.

To reset max throw: Let go of controls and press SET.

The menu tree below shows how to navigate through

the TQi transmitter’s various settings and functions.

Press and hold MENU to enter the menu tree, and use

the following commands to navigate through the menu

and select options.

MENU: When you enter a menu, you always start at the

top. Press MENU to move down the menu tree.

When you reach the bottom of the tree, pressing

MENU again will return you to the top.

SET: Press SET to move across the menu tree and select

options. When an option is committed to the

transmitter’s memory, the status LED will rapidly

blink green.

BACK: Press both MENU and SET to go back one level in

the menu tree.

EXIT: Press and hold MENU to exit programming.

Your selected options will be saved.

ECHO: Press and hold SET to activate the “echo” function.

Echo will “play back” your current position on the

Menu Tree, should you lose your place. For example:

If your current position is Steering Channel End

Points, holding SET will cause the LED to blink green

twice, green once, and then red three times. Echo

will not alter your adjustments or change your

position in the programming sequence.

MENU TREE

Below is an example of how to access a function in the menu

tree. In the example, the user is setting the Multi-Function knob

to be a steering Dual Rate control.

To set the Multi-Function knob to control STEERING DUAL RATE (%):

1. Switch the transmitter on

2. Press and hold MENU until the green LED lights. It will blink in single

intervals.

3. Press SET. The red LED will blink in single intervals to indicate Steering

Dual Rate has been selected.

4. Press MENU twice. The red LED will blink three times repeatedly to

indicate Steering Percentage has been selected.

5. Press SET to select. The green LED will blink 8 times fast to indicate

successful selection.

6. Press and hold MENU to return to driving mode.

Restoring Factory Defaults:

Transmitter

OFF

Hold both

MENU and SET

Transmitter

Release MENU and SET

red LED blinks

Press MENU 3 times

. The

transmitter LED will blink

red 4 times repeatedly.

Press SET to clear settings. LED

will turn solid green. Transmitter

is restored to default

1 2 ... 33 34 35 36 37 38 39 40

Commentaires sur ces manuels

Pas de commentaire

Traxxas 48077 Manuel d'utilisateur Page 38

Commentaires sur ces manuels

Produits connexes et manuels pour Jouets Traxxas 48077