Traxxas 68086-1 Manuel d'utilisateur télécharger pdf (Page 15)

SLASH 4x4

•

TRAXXAS TQ

RADIO & VELINEON POWER SYSTEM

6, 7

Using Reverse: While driving,

push the throttle trigger

forward to apply brakes.

Once stopped, return the

throttle trigger to neutral.

Push the throttle trigger

forward again to engage

proportional reverse.

USING THE RADIO SYSTEM

The TQi Radio System has been pre-adjusted at the factory. The

adjustment should be checked before running the model in case of

movement during shipping. Here’s how:

1. Turn the transmitter switch on. The status LED on the transmitter

should be solid green (not flashing).

Elevate the model on a block or a stand so that all the tires are

off the ground. Make sure your hands are clear of the moving

parts of the model.

Plug the battery pack in the model into the speed control.

The on/off switch is integrated into the speed control. With the

transmitter on, press and release the EZ-Set button (.25 seconds).

The LED will shine RED or GREEN (see note below).This turns

the model on. To turn the VXL-3s off, press and hold the EZ-Set

button until the LED turns off (.5 seconds). Note: If the model

is factory equipped with LiPo batteries, the LED will be green,

indicating that Low-Voltage Detection is activated. If the model

is factory equipped with NiMH batteries, the LED will be red,

indicating that Low-Voltage Detection is disabled. Never use

LiPo batteries while Low-Voltage Detection is disabled. See

page 17 for more information on Low-Voltage Detection.

Turn the steering wheel on the transmitter back and forth and

check for rapid operation of the steering servo. Also, check that

the steering mechanism is not loose or binding. If the steering

operates slowly, check for weak batteries.

When looking down at the model, the front wheels should be

pointing straight ahead.

If the wheels are turned

slightly to the left or right,

slowly adjust the steering

trim control on the

transmitter until they are

pointing straight ahead.

Gently operate the throttle trigger to ensure that you have

forward and reverse operation, and that the motor stops when

the throttle trigger is at neutral. Warning: Do not apply full

throttle in forward or reverse while the model is elevated.

8. Once adjustments are made, turn off the receiver on your model,

followed by the hand-held transmitter.

Range-Testing the Radio System

Before each running session with your model, you should range-test

your radio system to ensure that it operates properly.

Turn on the radio system and check its operation as described in

the previous section.

Have a friend hold the model. Make sure hands and clothing are

clear of the wheels and other moving parts on the model.

Make sure your transmitter antenna is fully extended, and then

walk away from the model with the transmitter until you reach

the farthest distance you plan to operate the model.

Operate the controls on the transmitter once again to be sure

that the model responds correctly.

Do not attempt to operate the model if there is any problem

with the radio system or any external interference with your

radio signal at your location.

Higher Speeds Require Greater Distance

The faster you drive your model, the more quickly it will near the

limit of radio range. At 60mph, a model can cover 88 feet every

second! It’s a thrill, but use caution to keep your model in range.

If you want to see your model achieve its maximum speed, it

is best to position yourself in the middle of the truck’s running

area, not the far end, so you drive the truck towards and past

your position. In addition to maximizing the radio’s range, this

technique will keep your model closer to you, making it easier to

see and control.

No matter how fast or far you drive your model, always leave

adequate space between you, the model, and others. Never drive

directly toward yourself or others.

TQi Binding Instructions

For proper operation, the transmitter and receiver must be

electronically “bound.” This has been done for you at the factory.

Should you ever need to re-bind the system or bind to an additional

transmitter or receiver, follow these instructions. Note: The receiver

must be connected to a 4.8-6.0v (nominal) power source for binding,

and the transmitter and receiver must be within 5 feet of each other.

1. Press and hold the transmitter’s SET button as you switch the

transmitter on. The transmitter’s LED will flash red slowly.

Release the SET button.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 33 34

Commentaires sur ces manuels

Pas de commentaire

Traxxas 68086-1 Manuel d'utilisateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Jouets Traxxas 68086-1